RP160

Digital Portable Vault Instruction Manual(RP160)

Battery Installation

  1. To get started, insert one of your backup keys into the keyhole at the front of the safeand insert one of your backup keys into the keyhole at the front of the safe. Push key in and rotate the key 30 degrees anticlockwise (LEFT) to open the safe.
  2. Locate the battery compartment door on the inside of the safe directly behind the keypad.
  3. Open the battery cover and insert the 4 AA alkaline batteries (not included) into the battery compartment. Note that pay attention to the “+”and “-”  The “-” end of the batteries go against the spring inside of the compartment.
  4. When the batteries are inserted correctly you will hear a short beep once and the keypad will light up.
  5. Once you hear the beep and see the keypad light up green, place the batteries cover. You are now ready to program your safe.

IMPORTANT: Your RPNB® safe will automatically lock when you fully close the lid.

Master Code Programming

First time users should change the default code as soon as possible to prevent unauthorized access to your safe, so it should be kept confidential.

  1. Enter default code 1-2-3 on the keypad to open your safe.
  2. With the safe open, press and hold the "PROGRAM" button (3 seconds), the indicator light will flash green two times with the double beeps.
  3. Enter your NEW master code.
  4. Press the "PROGRAM" button to confirm, the indicator light will flash yellow two times with the double beeps.
  5. Enter your master code again, then press the “PROGRAM”button for  The indicator light will flash green two times with the double beeps. This tone confirms that the password has been reset.
  6. Now test the code. If you make a mistake and the new code will not work, simply start over with step 2.

TIP: Code Requirements

  • Your code can be a minimum of 3 and a maximum of 8 digits.For your security, the safe will time out and sleep for 2 minutes if 3 incorrect entries are made.
  • Two keys cannot be pressed simultaneously.
  • Programming a new code will overwrite your previous code.
  • Pressing the “PROGRAM”button, the indicator light will flash green once with one deep.

RFID Programming Key Card/Key Fob/Self-adhesive Label

  1. Open the safe.
  2. Program RFID Programming Key Card/Key Fob/Self-adhesive Label by pressing and holding the “PROGRAM”button (3 seconds), the indicator light will flash green two times with the double beeps.
  3. Place the RFID Programming Key Card/Key Fob/Self-adhesive Label over theRFID Sign on the keypad approximately 1/4" from the surface for the scan. The indicator light flash yellow twice with two beeps, and then the indicator light flash green twice with two beeps remove your key card. This tone confirms that the key card has been reset.
  4. Now test the RFID Programming Key Card/Key Fob/Self-adhesive Label. If you make a mistake and the new key card will not work, simply start over with step 2.

Helpful Tips:

Before using the RFID Programming Key Card/Key Fob/Self-adhesive Label, you must press anyone of “1,2,3” button at first, then place your key fob/key card over the RFID induction zone to open the safe.

Deleting RFID Programming Key Card/Key Fob/Self-adhesive Label

  1. Open the safe.
  2. Press and hold the "PROGRAM" button (3 seconds), the indicator light will flash green two times with the double beeps. DO NOT RELEASE YOUR HAND. Hold the “PROGRAM”button (another 3 seconds), the indicator light will flash green two times with the double beeps. The RFID Programming Key Card/Key Fob/Self-adhesive Label has been deleted.
  3. Now test the RFID ProgrammingKey Card/Key Fob/Self-adhesive Label. If you make a mistake, simply start over with step 2.

TIP: This procedure will not affect the keypad master code. Keypad master code can not be deleted on the safe.

Silence Mode Setting

To silence the audible sound of the electronics, hold the “1” button for 3 seconds until you hear one beep and all the lights will flash together. To unmute the keys, repeat this step.

Low Battery Warning

If the indicator light will light up green and yellow simultaneously when opening the safe, your battery level is critically low and your safe needs to be replaced the new batteries.

Using the Mounting Screws

TIP: Make sure you have enough clearance for the lid to open properly before mounting the safe.

  1. Position the safe on a flat surface where you want to mount it.
  2. Use a pencil to mark the holes for drilling.
  3. Drill pilot holes.
  4. Position safe in place and install screws through safe into pilot holes. Tighten screws.

IMPORTANT: Do not let the safe door face the floor when you mounting the safe with the vertical direction to avoid your property from damage.